Ara
Toplam kayıt 53, listelenen: 1-10
Linear analysis of chatter vibration and stability for orthogonal cutting in turning
(2011)
The productivity of high speed milling operations is limited by the onset of self-excited vibrations known as chatter. Unless avoided, chatter vibrations may cause large dynamic loads damaging the machine spindle, cutting ...
Two new pyridine-2,3-dicarboxylate coordination polymers prepared from zerovalent metal precursor: Syntheses, luminescent and magnetic properties
(Academic Press Inc Elsevier Science, 2014)
Two new K+/Cu(II) and Zn(II) coordination polymers with pyridine-2,3-dicarboxylate (pydc), {K-2[Cu(mu-PYdc)(2)] center dot 3H(2)O}(n) (1) and {[Zn(mu-pydc)(H2O)(4-mim)] center dot H2O}(n) (2) (4-mim=4-methylimidazole) have ...
Reduction of cogging torque and improvement of electrical parameters in axial flux permanent magnet (AFPM) synchronous generator with experimental verification
(Electromagnetics Academy, 2020)
This paper presents an axial flux permanent magnet (AFPM) synchronous generator that was manufactured for the reduction of cogging torque by considering the different angles of a rectangle-shaped permanent magnet (RSPM). ...
Effect of substituent groups on the structures of two semi-flexible bis(imidazole) directed Zn(II)-5-sulfoisophthalate coordination polymers: Syntheses, structures and photoluminescent properties
(Pergamon-Elsevier Science Ltd, 2018)
Two new metal organic architectures, formulated as {(pbetixH(2))(0.5)[Zn(mu-sip)(mu-pbetix)(0.5)]}(n) (1) and {[Zn-2(mu-sip)(2)(pbisopix)(pbisopixH)(2)]center dot 4H(2)O}(n) (2), were synthesized based on the rarely employed ...
Decomposition of Process Damping Ratios and Verification of Process Damping Model for Chatter Vibration
(2012)
In the previous study, by the same authors, titled ‘‘A new process damping model (PDM) for chatter vibration (Measurement, 44 (8) (2011) 1342–1348)’’, a new approach has been presented for obtaining process damping ratios ...
A simple approach to analyze process damping in chatter vibration
(2014)
This paper investigates how changes in chatter amplitude and frequency depend on process damping effect in dynamic turning process. For this purpose, the two degrees of freedom (TDOF) cutting system was modeled, and for ...
Optimization of tool geometry parameters for turning operations based on the response surface methodology
(2011)
This investigation focuses on the influence of tool geometry on the surface finish obtained in turning of AISI 1040 steel. In order to find out the effect of tool geometry parameters on the surface roughness during ...
Syntheses and photoluminescence properties of new Zn(II) and Cd(II) coordination polymers prepared from 5-sulfoisophthalate ligand
(2017)
New coordination polymers, formulated as {[Zn(µ-sipH)(µ-apim)]·3H2 O} n (1) and {[Cd(µ-sip)(H2 O) 2 (apimH)]·3H2 O} n (2) were synthesized based on the 1-(3-aminopropyl)imidazole (apim) along ...
Application of Phase Change Materials to Pre-Heating of Evaporator and Pressure Regulator of a Gaseous Sequential Injection System
(2011-07-23)
The vehicle engines having gaseous sequential injection systems of liquefied petroleum gas (LPG) are operated on gasoline until the engine coolant reaches the required temperature because the heat of the engine coolant ...
Syntheses, structure and spectral studies of a new highly luminescent Cd(II)-5-sulfoisophtlialate coordination polymer
(Taylor & Francis Inc, 2018)
A new coordination polymer, [Cd-2(mu(3)-sip)(2)(etim)(6)Cd(etim)(2)](n) (1) (sip = 5-sulfoisophtalate, etim = 2-ethylimidazole) has been synthesized and characterized by elemental analysis, spectral (FT-IR and photoluminescence) ...